Micro Ore Milling Equipment

2017-12-21 11:24:16

Micro Ore Milling Equipment can be used for kaolin, limestone, calcite, marble, talc, barite, gypsum, dolomite, bentonite, mica, pyrophyllite, sepiolite, diatomaceous earth, graphite, alunite, fluorite, Ore and other humidity less than 6%, Mohs hardness of not more than 6 kinds of non-flammable and explosive materials for ultrafine Micro Ore Milling Equipment processing, finished particle size 325-2500 mesh, according to the actual requirements of the arbitrarily adjusted.

Micro Ore Milling Equipment Application

Micro Ore Milling Equipment material after crushing Micro Ore Milling Equipment, the specific surface area increases, its optical, magnetic, thermal, electrical, chemical reaction rate, dispersion, adsorption, mobility, reinforcing, filling, sinterability and other properties are produced Unexpected changes can be widely used in chemical, metallurgy, packing, pigments, abrasives, coatings, refractories, electrophotographic carrier, ceramics, medicine, food, cosmetics, composite materials and other industries. With the development of science and technology, the role and status of ultrafine grinding technology in the civil economy has become increasingly prominent.

Micro Ore Milling Equipment Working Principle

Micro Ore Milling Equipment chunks of materials crushed by hammer Micro Ore Milling Equipment into small particles by the elevator into the storage silo, and then through the vibrating feeder and the inclined feeding pipe, the material evenly to the top of the turntable bulk tray on.

Under the action of centrifugal force, the material scatters to the periphery and falls into the raceway of the grinding ring, which is impacted by the ring roll, rolled, ground and processed into Micro Ore Milling Equipment by the processing of the three-layer circular path. The high-pressure fan draws the outside air Inhaled machine, and the crushed material into the separator.

Pulverizer within the rotating impeller coarse material down to reground, meet the requirements of the fine Micro Ore Milling Equipment is with the air into the cyclone Micro Ore Milling Equipment collector and discharge valve from the bottom is the finished product, and with a small amount of fine dust flow After pulsed dust collector purifier through the fan and muffler discharge.

Micro Ore Milling Equipment Routine Maintenance And Repair

• 1, always check the bearing temperature, if the temperature is too high, should check the lubrication and transmission part is normal, rolling distance is too tight and so on. Timely identify the reasons, take appropriate measures, the situation should be stopped down inspection.
 
• 2, always check the tightness of the belt, the belt is too loose will reduce the transmission efficiency and affect the grinding effect, too tight is likely to cause bearing fever, increase power consumption and reduce the service life of the belt.
 
• 3, all kinds of transmission components must be fastened and reliable, disassembly or installation should use special tools, prohibit the use of hand hammer and other tools directly hit.
 
• 4, do not forget to check the pneumatic components, the mill boot, we should always check the gas in the pneumatic components, gas and connections for leaks or damage, and to check whether the supply pressure meets the requirements of the timing belt Use should also be checked frequently, if found too tight, too loose, beating, deviation, serious wear and tear, etc., should be promptly adjusted, overhaul or replacement. Gas source triplet oil mist in the amount of oil to be checked regularly, you must add 20 spindle oil, so as to avoid pipeline congestion.
 
• 5, timely inspection of the oil circuit, mill oil pump oil, according to the temperature level of 20 to 40 mechanical oil, or other viscosity of the same hydraulic oil, oil inspection every six months to clear the impurities in the oil.
 
• 6, regularly and regularly replace the grinding roller, grinding roller can not be replaced twice too much, while the diameter of the roller can not be too large, the angle of the roller, the pitch, the number of teeth to comply with the provisions to be left with two fixed teeth flat. Roller taper of each section should be accurate and meet the requirements, the surface roughness should be uniform. After replacing the grinding roller, the grinding system should be the requirements of each system, with feeler inspection, rough rolling distance.