...

Clinker Crusher


2018-09-14 10:47:20

Clinker Crusher

Maintenance of Clinker Crusher

Clinker Crusher is a common crushing equipment in sand production line and crushing production line. It is well-known for its good granularity. It is very important to do a good job of equipment maintenance if you want Clinker Crusher to serve you steadily for a long time. Today Xiaobian brings Clinker Crusher maintenance to you. It is hoped that the users will do a good job in the maintenance and repair of the Clinker Crusher, and strangle the problem in the budding state, so as to ensure the normal and stable operation of the Clinker Crusher for a long time.

  • 1, after the new aircraft is put into operation, every class must have a comprehensive check on the counterattack.
  • 2, after running every week, we will conduct a comprehensive check on the motors and lubrication that have been broken down. The contents of the inspection include the fastening of fixed parts, belt drive, bearing seal, counterattack liner, liner wear and tear in full position inspection, and combined with the maintenance cycle to establish a regular maintenance and replacement system.
  • 3. Clearance adjustment between rotor and backlash liner: When the rotor of Clinker Crusher is running, the clearance between rotor and backlash liner can not be adjusted. If the material blocks stay between the counterattack plate and the shell, it is recommended to lift the counterattack rack slightly between the readjustment clearance, so that the block feeding will become loose and the counterattack rack is easy to adjust. If the counterattack frame is not sufficient, tap it on the relaxed pull rod (protected by a board). The clearance between the rotor and the counterattack lining is accomplished by adjusting the machine. The bolt sleeve is loosened first, and then the long nut is rotated. At this time, the pull rod moves upward and the screw sleeve is tightened.
  • 4, replace vulnerable parts: when the Clinker Crusher changes the vulnerable parts, first open and then rack. When in use, the connecting bolt of the rear upper rack and the middle box body is unloaded, and then the hexagon head of the overturning device is screwed by a wrench, and the upper rack is opened slowly. At the same time, the rear frame can be hung by hanging device above the rack. Repeat the above process, that is, close the shelves.
  • 5. Plate hammer: When the counterattack breaking plate hammer is worn to a certain extent, it should be adjusted or replaced in time to avoid damage to fasteners and other parts.
  • 6. Lining plate: Open the back cover, remove the open pin, slotted nut and bolt used to fix the backing plate, and replace the worn backing plate. If you install a new counterattack lining board, reverse the above steps immediately.
  • 7. Bearings: Excessive temperature may be due to excessive or inadequate grease, grease dirty, bearing damage, replacement of the bearing Clinker Crusher in the sand production line plays a key step.
...
Leave Message

...
Raw Ore Milling Equipment In Cement Plant 2018-09-14 10:47:20

Precautions of Raw Ore Milling EquipmentA company's 2000t/d new dry process cement production line and raw meal preparation system adopt Raw Ore Milling Equipme

...
Roller Ore Milling Equipment For Sale 2018-09-14 10:47:20

Roller Ore Milling Equipment Vibration ReasonThe Roller Ore Milling Equipment is very easy to stop in the later operation, and there are many reasons for the vi

...
Continuous Ball Ore Milling Equipment 2018-09-14 10:47:20

Continuous Ball Ore Milling Equipment "Run Rough"Continuous Ball Ore Milling Equipment is widely used in mine, metallurgy, cement and other industries. It is an

...
Garnet Ore Milling Equipment 2018-09-14 10:47:20

Installation and maintenance of Garnet Ore Milling EquipmentThe maintenance of Garnet Ore Milling Equipment is a very important and regular job. It should coope

...
Cement Vertical Ore Milling Equipment 2018-09-14 10:47:20

How To Improve The Performance Of Cement Vertical Ore Milling EquipmentVertical Ore Milling Equipment in the coal mine is widely used, with China's economy and

...
T130X Strengthen Ultrafine Mill 2018-09-14 10:47:20

T130X Strengthen Ultrafine Mill, which is based on the market research, and statistically analyzes the user's usage and suggestions in many mills, and innovatin



Categories
Project
News